BlinkenLEDsPlusColourEnglish: Difference between revisions

From BlinkenArea Wiki
Jump to: navigation, search
No edit summary
No edit summary
 
(One intermediate revision by the same user not shown)
Line 23: Line 23:
The project is powered by an external power supply which must be capable of supplying 5 V with at least 1.5 A.
The project is powered by an external power supply which must be capable of supplying 5 V with at least 1.5 A.


* [[:Media:BPC-instructions-rev1.0.pdf|Construction Kit Instructions Rev. 1.0]] for PCB Rev. 1.0 and Rev. 1.1
=== Rev. 1.1 ===
With corrected RxD and TxD connections.
* [[:Image:BPC-rev1.1-schematic.png|Schematic Rev. 1.1]] (PNG)
* [[:Media:BPC-rev1.1.sch|Schematic Rev. 1.1]] (Eagle 4.x)
* [[:Media:BPC-rev1.1.brd|PCB Layout Rev. 1.1]] ('''half size''', Eagle 4.x)
=== Rev. 1.0 ===
With swapped RxD and TxD connections between MAX232 and AVR.
* [[:Image:BPC-rev1.0-schematic.png|Schematic Rev. 1.0]] (PNG)
* [[:Image:BPC-rev1.0-schematic.png|Schematic Rev. 1.0]] (PNG)
* [[:Media:BPC-rev1.0.sch|Schematic Rev. 1.0]] (Eagle 4.x)
* [[:Media:BPC-rev1.0.sch|Schematic Rev. 1.0]] (Eagle 4.x)
Line 28: Line 38:
* [[:Media:BPC-rev1.0-gerber-controller.zip|Controller PCB Layout Rev. 1.0]] (Gerber files)
* [[:Media:BPC-rev1.0-gerber-controller.zip|Controller PCB Layout Rev. 1.0]] (Gerber files)
* [[:Media:BPC-rev1.0-gerber-leds.zip|LED PCB Layout Rev. 1.0]] (Gerber files)
* [[:Media:BPC-rev1.0-gerber-leds.zip|LED PCB Layout Rev. 1.0]] (Gerber files)
* [[:Media:BPC-rev1.0-instructions.pdf|Construction Kit Instructions Rev. 1.0]]


== Software ==
== Software ==

Latest revision as of 15:42, 7 August 2016

project overview
Zur deutschsprachigen Version dieser Seite
BPC.jpg
Year 2015
Number of pixels 144
Grayscales / Colors RGB, 83 = 512 colours
Illuminant 5 mm LEDs
Power input 7.5 W
Contact person Arne Rossius
Project website


BlinkenLEDs Plus Colour is a project with the BlinkenLights resolution and pixel aspect ratio. It is the same size as the BlinkenLEDs Plus, but uses RGB LEDs to enable playing coloured animations.

Hardware

Just as the BlinkenLEDs Plus, this project is using an LED board and a control board which are stacked and connected through pin headers.

The LED matrix is made up of three times 8 rows (for red, green and blue) and 18 columns. The multiplexing is done over the columns from left to right, the refresh rate being 100 Hz for the lowest brightness level and increasing for pixels with higher brightness. Blinken movies can be played from an SD card or from an MCUF stream through a serial RS232 port. In addition, an MCUF stream of all displayed frames is output on the same port at all times.

The project is powered by an external power supply which must be capable of supplying 5 V with at least 1.5 A.

Rev. 1.1

With corrected RxD and TxD connections.

Rev. 1.0

With swapped RxD and TxD connections between MAX232 and AVR.

Software

This project uses the BlinkenPlus firmware.

Photos

More photos at http://arne.blinkenarea.org/BlinkenLEDs%20Plus%20Colour/gallery.htm.