BlinkenLEDsPlusColourEnglish: Difference between revisions

From BlinkenArea Wiki
Jump to: navigation, search
m (ArneRossius moved page BlinkenLEDsPlusColorEnglish to BlinkenLEDsPlusColourEnglish without leaving a redirect)
No edit summary
 
(4 intermediate revisions by the same user not shown)
Line 1: Line 1:
Coming soon ...
__NOEDITSECTION__
{{InfoboxEnglish
|Name=BlinkenLEDsPlusColour
|Bild=BPC.jpg
|Jahr=2015
|Pixel=144
|Farben=RGB, 8<sup>3</sup> = 512 colours
|Leuchtmittel=5 mm LEDs
|Leistung=7.5 W
|Kontakt=[[User:ArneRossius|Arne Rossius]]
|Webseite=
}}
 
 
BlinkenLEDs Plus Colour is a project with the BlinkenLights resolution and pixel aspect ratio. It is the same size as the [[BlinkenLEDsPlusEnglish|BlinkenLEDs Plus]], but uses RGB LEDs to enable playing coloured animations.
 
== Hardware ==
 
Just as the BlinkenLEDs Plus, this project is using an LED board and a control board which are stacked and connected through pin headers.
 
The LED matrix is made up of three times 8 rows (for red, green and blue) and 18 columns. The multiplexing is done over the columns from left to right, the refresh rate being 100&thinsp;Hz for the lowest brightness level and increasing for pixels with higher brightness. Blinken movies can be played from an SD card or from an [[MCUFEnglish|MCUF]] stream through a serial RS232 port. In addition, an MCUF stream of all displayed frames is output on the same port at all times.
 
The project is powered by an external power supply which must be capable of supplying 5&thinsp;V with at least 1.5&thinsp;A.
 
* [[:Media:BPC-instructions-rev1.0.pdf|Construction Kit Instructions Rev. 1.0]] for PCB Rev. 1.0 and Rev. 1.1
 
=== Rev. 1.1 ===
With corrected RxD and TxD connections.
* [[:Image:BPC-rev1.1-schematic.png|Schematic Rev. 1.1]] (PNG)
* [[:Media:BPC-rev1.1.sch|Schematic Rev. 1.1]] (Eagle 4.x)
* [[:Media:BPC-rev1.1.brd|PCB Layout Rev. 1.1]] ('''half size''', Eagle 4.x)
 
=== Rev. 1.0 ===
With swapped RxD and TxD connections between MAX232 and AVR.
* [[:Image:BPC-rev1.0-schematic.png|Schematic Rev. 1.0]] (PNG)
* [[:Media:BPC-rev1.0.sch|Schematic Rev. 1.0]] (Eagle 4.x)
* [[:Media:BPC-rev1.0.brd|PCB Layout Rev. 1.0]] ('''half size''', Eagle 4.x)
* [[:Media:BPC-rev1.0-gerber-controller.zip|Controller PCB Layout Rev. 1.0]] (Gerber files)
* [[:Media:BPC-rev1.0-gerber-leds.zip|LED PCB Layout Rev. 1.0]] (Gerber files)
 
== Software ==
 
This project uses the [[BlinkenPlusEnglish|BlinkenPlus]] firmware.
 
== Photos ==
 
More photos at http://arne.blinkenarea.org/BlinkenLEDs%20Plus%20Colour/gallery.htm.
 
[[Category:Projects]]
[[Category:BlinkenPlusProjects]]

Latest revision as of 15:42, 7 August 2016

project overview
Zur deutschsprachigen Version dieser Seite
BPC.jpg
Year 2015
Number of pixels 144
Grayscales / Colors RGB, 83 = 512 colours
Illuminant 5 mm LEDs
Power input 7.5 W
Contact person Arne Rossius
Project website


BlinkenLEDs Plus Colour is a project with the BlinkenLights resolution and pixel aspect ratio. It is the same size as the BlinkenLEDs Plus, but uses RGB LEDs to enable playing coloured animations.

Hardware

Just as the BlinkenLEDs Plus, this project is using an LED board and a control board which are stacked and connected through pin headers.

The LED matrix is made up of three times 8 rows (for red, green and blue) and 18 columns. The multiplexing is done over the columns from left to right, the refresh rate being 100 Hz for the lowest brightness level and increasing for pixels with higher brightness. Blinken movies can be played from an SD card or from an MCUF stream through a serial RS232 port. In addition, an MCUF stream of all displayed frames is output on the same port at all times.

The project is powered by an external power supply which must be capable of supplying 5 V with at least 1.5 A.

Rev. 1.1

With corrected RxD and TxD connections.

Rev. 1.0

With swapped RxD and TxD connections between MAX232 and AVR.

Software

This project uses the BlinkenPlus firmware.

Photos

More photos at http://arne.blinkenarea.org/BlinkenLEDs%20Plus%20Colour/gallery.htm.