ChaosknotenEnglish: Difference between revisions

From BlinkenArea Wiki
Jump to: navigation, search
(Created page with "__NOEDITSECTION__ {{Infobox |Name=Chaosknoten |Bild=BlinkenArea-CCC-Chaosknoten_(front).jpg |Jahr=2019 |Pixel=42 |Farben=16 Graustufen (gamma 2.0) |Leuchtmittel=SMD LEDs |Leis...")
 
No edit summary
Line 14: Line 14:
Chaosknoten - this is a small circuit board of 65 x 50mm, which uses 42 LEDs to show the official logo of [https://de.wikipedia.org/wiki/Chaos_Computer_Club logo of Chaos Computer Club]. The orange LEDs display several animations using 16 brightness levels (gamma = 2.0). DThe board is powered by a single CR2032 button cell. On the backside there are two switches - one to turn it on and off, and the other one can be used to freeze the animation (freeze frame).
Chaosknoten - this is a small circuit board of 65 x 50mm, which uses 42 LEDs to show the official logo of [https://de.wikipedia.org/wiki/Chaos_Computer_Club logo of Chaos Computer Club]. The orange LEDs display several animations using 16 brightness levels (gamma = 2.0). DThe board is powered by a single CR2032 button cell. On the backside there are two switches - one to turn it on and off, and the other one can be used to freeze the animation (freeze frame).


The logo is designed by [https://de.wikipedia.org/wiki/Wau_Holland Wau Holland]. We are authorized by the [https://www.wauland.de/ Wau Holland Stiftung] to provid this kit as long as we don't make any profit with it and we provid the layout information and software for free.  
The logo is designed by [https://de.wikipedia.org/wiki/Wau_Holland Wau Holland]. We are authorized by the [https://www.wauland.de/ Wau Holland Stiftung] to provide this kit as long as we don't make any profit with it and we provide the layout information and software for free.  


This project ist based on the [[bulb]].
This project ist based on the [[bulb]].


=== Downloads (firmware, layout, curcuit layout) ===
=== Downloads (firmware, layout, circuit layout) ===


* [https://git.blinkenarea.org/?p=Chaosknoten Blinkenarea Chaosknoten GIT-Repository]
* [https://git.blinkenarea.org/?p=Chaosknoten Blinkenarea Chaosknoten GIT-Repository]

Revision as of 11:43, 21 June 2019

zur Projektübersicht
English Version of this Page
BlinkenArea-CCC-Chaosknoten (front).jpg
Jahr 2019
Anzahl Pixel 42
Graustufen / Farben 16 Graustufen (gamma 2.0)
Leuchtmittel SMD LEDs
Leistungsaufnahme 120mW
Kontaktperson Stefan Schuermans, ST
Projekt-Website BlinkenArea Chaosknoten

Chaosknoten - this is a small circuit board of 65 x 50mm, which uses 42 LEDs to show the official logo of logo of Chaos Computer Club. The orange LEDs display several animations using 16 brightness levels (gamma = 2.0). DThe board is powered by a single CR2032 button cell. On the backside there are two switches - one to turn it on and off, and the other one can be used to freeze the animation (freeze frame).

The logo is designed by Wau Holland. We are authorized by the Wau Holland Stiftung to provide this kit as long as we don't make any profit with it and we provide the layout information and software for free.

This project ist based on the bulb.

Downloads (firmware, layout, circuit layout)

Version 1.0.0

  • Chaosknoten board front
  • Chaosknoten board back
  • Chaosknoten circuit layout

Images

  • Chaosknoten front
  • Chaosknoten back
  • Instructions for assembling the kit 1.0.0

    1. Chaosknoten-1.0.pdf öffnen
    2. Seite 1 und 2 aus "Chaosknoten-1.0.pdf" ansehen
    3. LEDs wie im PDF auf Seite 2 gezeichnet auflöten (Die schwarzen Punkte neben den LEDs im PDF zeigen an, wo die grünen Punkte der echten LED hingehören.)
    4. Seite 2 aus "Chaosknoten-1.0.pdf" ansehen
    5. Widerstand (winzig, dunkel, Aufdruck "1002") auf Position R1 einlöten (Polarität ist egal)
    6. Kondensator (winzig, braun, kein Aufdruck) auf Position C1 einlöten
    7. FET (klein, schawrz, 8 Pins) auf Position T1 einlöten (Der Punkt auf dem Chip gehört an die Seite, die im PDF mit dem Halbkreis gekennzeichnet ist.)
    8. Microcontroller (größer, schwarz, 20 Pins) auf Position IC1 einlöten (Der Punkt auf dem Chip gehört an die Seite, die im PDF mit dem Halbkreis gekennzeichnet ist.)
    9. Taster (scharz, zwei kleine weisse Hebel, 4 Pins) auf Position S1 einlöten. (der kleine Kringel markiert Pin 1. Pin 1 ist dort, wo die Zahl 1 aufgedruckt ist)
    10. Batteriehalter auf Position B1 einlöten
    11. Batterie einlegen