AntiKippenLights-MiniEnglish: Difference between revisions

From BlinkenArea Wiki
Jump to: navigation, search
No edit summary
No edit summary
 
(One intermediate revision by the same user not shown)
Line 13: Line 13:


AntiKippenLights-Mini is an [[AntiKippenLightsEnglish|AntiKippenLights]] in the size of a matchbox. It consists of 18 SMD LEDs (size 0805) that are, unlike in the original, driven by an Atmel ATtiny2313 microcontroller. Starting from version 2.0, an ATtiny24A is used instead. The device is powered by a single CR2032 3 V lithium button cell. The circuit can be switched on and off with the button. When it is switched off, it draws only approx. 200 nA which in most cases will be less than the battery's self discharge current. To prevent an empty battery when the circuit has bad contact to the battery, it switches itself off when the battery is (re)connected.
AntiKippenLights-Mini is an [[AntiKippenLightsEnglish|AntiKippenLights]] in the size of a matchbox. It consists of 18 SMD LEDs (size 0805) that are, unlike in the original, driven by an Atmel ATtiny2313 microcontroller. Starting from version 2.0, an ATtiny24A is used instead. The device is powered by a single CR2032 3 V lithium button cell. The circuit can be switched on and off with the button. When it is switched off, it draws only approx. 200 nA which in most cases will be less than the battery's self discharge current. To prevent an empty battery when the circuit has bad contact to the battery, it switches itself off when the battery is (re)connected.
Also see: [[LedShapesEnglish|LedShapes]].


== Prototype ==
== Prototype ==
Line 33: Line 35:


==== Heart ====
==== Heart ====
* [[:Media:AKLM-2.0.brd|PCB layout]] (EAGLE 4.x)
* [[:Media:AKLM-2.0-heart.brd|PCB layout]] (EAGLE 4.x)
* [[:Media:AKLM-2.0.pdf|Construction kit instructions]]
* [[:Media:AKLM-2.0-heart-instructions.pdf|Construction kit instructions]]


=== Rev. 1.4 ===
=== Rev. 1.4 ===

Latest revision as of 20:56, 30 September 2023

project overview
Zur deutschsprachigen Version dieser Seite
Antikippenlightsmini-03.jpg
Year 2005
Number of pixels 18
Grayscales / Colors greyscales
Illuminant SMD LEDs
Power input
Contact person Arne Rossius
Project website

AntiKippenLights-Mini is an AntiKippenLights in the size of a matchbox. It consists of 18 SMD LEDs (size 0805) that are, unlike in the original, driven by an Atmel ATtiny2313 microcontroller. Starting from version 2.0, an ATtiny24A is used instead. The device is powered by a single CR2032 3 V lithium button cell. The circuit can be switched on and off with the button. When it is switched off, it draws only approx. 200 nA which in most cases will be less than the battery's self discharge current. To prevent an empty battery when the circuit has bad contact to the battery, it switches itself off when the battery is (re)connected.

Also see: LedShapes.

Prototype

The prototype is still the same size as the AntiKippenLights, but it already consists of the parts that will be used in the AntiKippenLights-Mini. The source code that was written for a PIC microcontroller was ported to AVR almost literally, thus the animations are somewhat slower. In addition, the LEDs have a different order, so some animations will start at a different LED than on the original AntiKippenLights.

Hardware

The PCB measures 45.7 x 30.5 mm and fits exactly into a matchbox. The layout is double sided (of course) and it's recommendable to use thin PCB material (e.g. 1 mm). Up to Rev. 1.2, the button cell retainer is the same as the ones used on PC mainboards, so you can desolder one from a broken board. From Rev. 1.3 onward, an SMD button cell retainer is used. The resistors and the capacitor have to be size 0805, the same size as the LEDs.

Rev. 2.0

Heart

Rev. 1.4

Heart

Arrow

Rev. 1.3

Rev. 1.2

Software

For Hardware Rev. 2.x

These versions can run on the hardware versions based on ATtiny24(A) (controller with 14 pins).

  • Version 2.0.0 (first version for ATtiny24, based on version 1.0.0)

For Hardware Rev. 1.x

These versions can run on all hardware versions based on ATtiny2313(A) (controller with 20 pins).

Photos

http://arne.blinkenarea.org/akl-mini/