BlinkstroemColourEnglish: Difference between revisions
ArneRossius (talk | contribs) No edit summary |
ArneRossius (talk | contribs) No edit summary |
||
| Line 24: | Line 24: | ||
The 3.3 V power supply for the SD card is generated either by two silicon diodes in series or a 3.3 V regulator. If the diodes are used, C10A (100 nF) is populated, for the voltage regulator C10B (1 µF) is necessary. R38D is a basic load to prevent the voltage from becoming too high when no SD card is inserted, especially when using the diodes. | The 3.3 V power supply for the SD card is generated either by two silicon diodes in series or a 3.3 V regulator. If the diodes are used, C10A (100 nF) is populated, for the voltage regulator C10B (1 µF) is necessary. R38D is a basic load to prevent the voltage from becoming too high when no SD card is inserted, especially when using the diodes. | ||
=== Rev. 1.1 === | |||
With additional resistors to reduce ghosting. | |||
* [[:Image:Bsc-rev1.1.png|Schematic]] | |||
* [[Media:BSC-rev1.1.sch|Schematic]] (EAGLE file, version 4.16) | |||
* [[Media:BSC-rev1.1.brd|PCB layout]] (EAGLE file, version 4.16) | |||
* [[Media:BSC-rev1.2-instructions.pdf|Construction kit instructions]] | |||
=== Rev. 1.0 === | |||
* [[:Image:Bsc-rev1.png|Schematic]] | * [[:Image:Bsc-rev1.png|Schematic]] | ||
Revision as of 17:46, 27 December 2013
project overview  | |
| |
| Year | 2013 |
| Number of pixels | 144 |
| Grayscales / Colors | RGB, 83 = 512 colours |
| Illuminant | SMD LEDs |
| Power input | 4 W |
| Contact person | Arne Rossius |
| Project website | |
Blinkström Colour is a BlinkenLights clone that can display full colour animations.
This project uses the BlinkenPlus firmware on an ATmega162 controller. On the PCB there is an SD card slot as well as a level converter and solder pads for an RS232 serial port for streaming input and output.
Attention! The kit instructions from OHM2013 have the wrong capacitor identifiers. A corrected version is available for download below.
Hardware
The LED matrix is divided into 18 columns and three times 8 rows (8 each for red, green and blue). The multiplexing is going across the columns from right to left, so only one column is lit at a time. The refresh rate is 100 Hz for the lowest brightness level and increases for the higher brightness levels. The board has to be supplied from an external 5 V power supply capable of at least 0.8 A.
The 3.3 V power supply for the SD card is generated either by two silicon diodes in series or a 3.3 V regulator. If the diodes are used, C10A (100 nF) is populated, for the voltage regulator C10B (1 µF) is necessary. R38D is a basic load to prevent the voltage from becoming too high when no SD card is inserted, especially when using the diodes.
Rev. 1.1
With additional resistors to reduce ghosting.
- Schematic
- Schematic (EAGLE file, version 4.16)
- PCB layout (EAGLE file, version 4.16)
- Construction kit instructions
Rev. 1.0
- Schematic
- Schematic (EAGLE file, version 4.16)
- PCB layout (EAGLE file, version 4.16)
- Construction kit instructions
Animations
Unfortunately, only very few colour animations are available. If you create your own animations (e.g. using Blimp), you are very welcome to send them in. For now, some animations are available here: Full colour BlinkenLights animations.
Photos
More photos: http://arne.blinkenarea.org/BlinkstroemColour/gallery.htm
